Windows 10: Monitor keep losing signal after some times it is still happening

Previous postAnswers for previous postThe driver for GT 730 GT 730 30.0.14.7514 released on 10th July was unable to be installed because of incompatiblityThe cable were fineI didnt have any extra laptop to test the monitorNever Turn Off power option worked for a while but it is still turning off My monitor started doing this since 6th September friday night, the first issue was it crashing and breaking because of snip and sketch which is odd and it hasnt happened since, then the newly replaced GT 730 worked fine until literally just 2 hours later when my monitor decide to lose signal. Afte

:)

 

GTX 1050 ti Monitors Lose Signal

So far there's been a catalogue of symptoms, and the worrying thing is there are literally pages and pages of the same issue with GTX 1050's on the GeForce forums.

Symptoms so far:

• After getting to the logon screen, both my 4K monitor (plugged in via DP) and my 1080p monitor (plugged in via HDMI) spuriously lose signal for ~5 seconds then come back. This happens constantly with no apparent timing.

• Whenever I open a game launcher (not a game), or Google Chrome, the screen flickers again, only this time I get a Windows 10 event alert saying "application has been blocked from accessing graphics hardware".

• When I check event viewer System logs, the yellow triangle simply says "nvlddmkm stopped responding" in each case of the monitors losing signal.

Attempted fixes from numerous threads:

• Installed the latest Game Ready "stable" drivers, installed latest "beta" drivers, and also installed some random "stable" drivers from a month ago. Uninstalled previous drivers with DDU each time and restarted before and after installation. Issue seems to persist sporadically.
• Turned PCI Power Management off in Windows Power Settings. No change.
• Switched Power settings in NVidia Control Panel to Maximum Performance. No change.
• Gone into the registry and added a QWord(64bit) to CurrentControlSet001/Graphics/Drivers called "TdrDelay" and set it to 8 (also tried 10). No change.
• Tried unplugging the secondary monitor. Managed to play Warframe for an entire evening without a monitor signal loss.
• Switched secondary monitor to DVI Single Link cable to 1050 ti, and also tried secondary monitor on iGPU with primary monitor on 1050 ti. Still get signal losses on main monitor, secondary monitor does the same but is delayed (WTF?).
• Downclocked GPU 50Mhz. No change.
• Increased Power Limit by 5%. No change.

Fixes I still need to try:

• Try a different DP cable in main monitor/try HDMI cable instead.
  
• I get the signal loss when I open Chrome, going to turn off hardware acceleration as that apparently solves things
• Use a DWord(32bit) registry key instead of QWord for TdrDelay
• Going to try the 375.50 drivers, as they're allegedly old but stable for low power Pascal GPUs.
• Resetting CMOS for whatever reasons - some random guy said this solved his issues.

Fairly convinced it's not a hardware issue since there are so many people with the same issue as me. One slight glimmer of explanation is that Micron memory may be at fault, I need to check if its Samsung or Micron stuff on mine. Apparently there were some GTX 1070 stability issues with Micron VRAM that were fixed with an update.

My entire system has been stable for years, sporting a R9 295x2 up until 6 months ago with no stability problems. Doubt it's PSU related. Motherboard is also on the latest 2.50 BIOS.

Help me TPU, you're my only hope.

 

Monitors Lose Signal On Boot


I have 3 Benq xl2720z monitors all using dp.

In the morning I went to turn on my monitors to find out there was no signal in any of them. I then rebooted my computer and when I got to the spinning orb, my computers faded to black in the middle of it and lost signal. I didn't even get to the login screen.

I then decided to try each monitor by themselves starting with the left monitor. this monitor managed to the login and to the desktop. However it still faded to black as if it was about to lose signal in the middle of the spinning orb. However it managed to recover I guess and show the login. The part that I noticed is that it took much less time to normally to get to the login so something is not right.

I then tried the middle monitor. The first try I got to the desktop just to lose signal a second later. The second try I lost signal during the spinning orb.

For the right monitor, I lost signal when I got to the desktop. Didn't bother trying again with it.

Since the left monitor I could get somewhere I decided to go and plug that one in so I could go and write this, however I accidently plugged in the middle monitor but it was idea I did because something new happened.

I got to the login and desktop fine and it never faded to pure black in the middle of the spinning orb. It showed the whole animation but the second one with the blue screen. It also longer to boot up which was how it was suppose to be.

So I no idea what is going on. It all feels random. Can someone help me with this?

I'm going to try rebooting again and see if the middle monitor is fine now and then I'm going to try all 3 together.

EDIT: Tried again with the middle monitor, it booted without issues. Tried again with 3 monitors, it booted to desktop without going to no signal, however the boot was shorter. Is there a reason for Windows 10 to not go to the seconded spinning orb with the blue screen?

 

Monitor loses randomly loses signal.

This started happening a few weeks ago, and it happens randomly, even when I just browse the internet or do intensive GPU stuff like 3d modeling or gaming.

The monitor (samsung sj55w ultra wide) loses signal from the computer but the computer keeps working, as I hear the music or whatever runs in background, everything works fine after a restart but sometimes after the restart the resolution goes to 1280x1024 and AMD Adrenalin says that windows might have deleted my drivers, after I reinstall Adrenalin and restart the computer everything goes back to normal until it happens again for some reason.

GPU: RX 580 Sapphire Nitro+ 8GB (bought it from a second hand parts retailer and still have a few months of warranty)

CPU: Intel i3 6100

RAM: 16GB DDR4

PSU: Corsair CX 430

This is the error that I get for every single time when it loses signal:

Problem Event Name: LiveKernelEvent

Code: 141

Parameter 1: ffff8f8e701eb010

Parameter 2: fffff8003a395400

Parameter 3: 0

Parameter 4: 3c8

OS version: 10_0_19044

Service Pack: 0_0

Product: 256_1

OS Version: 10.0.19044.2.0.0.256.48

Locale ID: 1033

And this is the error that I get when the drivers fail after restart:

Problem Event Name: LiveKernelEvent

Code: 1b0

Parameter 1: 1

Parameter 2: ffffffffc0000001

Parameter 3: 0

Parameter 4: 0

OS version: 10_0_19044

Service Pack: 0_0

Product: 256_1

OS Version: 10.0.19044.2.0.0.256.48

Locale ID: 1033

I feel like the PSU 430W might not be enough for the GPU and the monitor and that might be the problem but I'm just guessing.