Windows 10: KB5018410 update causes problems with WIFI adapter.

System now gives error when using troubleshooter that the driver is not working properly It cannot link IP stacks to windows

:)

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?

 

WiFi Adapter question

To be honest, I keep losing my wifi connection and Im almost positive its not due to my internet connection or Router or anything like that. VERY often, everyday, all day it keeps happening. The troubleshooter always resolves it by "reset wifi-adapter" (I believe this is the step it takes that resolves the problem) before it happens again anyways.

Its driving me nuts !

Most time when it suddenly goes out (the connection) all the networks that should be in "show available networks" or all but the one I was connected to, disappear. I run the troubleshooter and it ends in resetting the wifi adapter. And it works. 10 minutes later, it happens again. Im trying to pin down the problem here.

Thank you for your help.

 

I keep losing my WiFi adapter

I tried the Option 2 approach but kept getting the Error NetSetupDeleteObjecton Network Adapter error (0x80070005) error, even after a dozen executions of the command. That seemed like it was going nowhere so I tried Option 1.

After completing the reboot in Option 1, I never got the dialog that asked if I wanted to make the computer discoverable, even after a significant wait.

Do you have any further suggestions? I'm going to move on to "Compumind's" suggestion in the meantime and see if that helps....

- - - Updated - - -

I started working my way down the list.

1. Both the ipv4 and ipv6 resets said "access denied!". However, the mere attempt worked *briefly*, then the WiFi went down again.
2. I disabled and re-enabled the network adapter. Again, it worked *briefly*, then I lost the WiFi again.
3. I tried to disable the antivirus but couldn't find a setting for that so uninstalled it entirely. I got the WiFi back and this time it stayed on for several hours instead of a few minutes so I assumed it was fixed. Then I installed the new Avast One and the WiFi is still working so I'm assuming that all is well finally!

Thank you for this list of suggestions!!!