Windows 10: Internet stopped working and says “You’re connected using a virtual network adapter.

says “You’re connected using a virtual network adapter that we can’t test”. I’m not using a virtual network adapter though

:)

 

Microsoft Hosted Virtual Network Adapter is Missing

Hi Arthur,

There's a possibility that the Internet Connection Sharing is not enabled on your machine. To enable it, follow the steps below:

• Right-click the Windows key, then select Network Connections.
• Right-click the network adapter with an Internet connection (could be Ethernet or wireless network adapter), then select
  Properties.
• Click Sharing tab.
• Under Internet Connection Sharing, check the Allow other network users to connect through this computer’s Internet connection option.
  
• On the Home networking connection drop-down menu, select the
  Microsoft Hosted Virtual Adapter.
• Click OK to finish.

Update us with the result.

Regards.

 

Set Broadband Internet Connection Network Configuration

Hi,

Upon analyzing the details you have provided, kindly run the
Network and Internet Troubleshooter
and check if there's any changes. To run the
troubleshooter,
follow these steps:

• 
  On the search bar, type
  Troubleshooting.
  
• 
  Choose
  Network and Internet.
  
• 
  Run the following
  Troubleshooter:
  
  • 
    Internet Connections.
    
  • 
    Network Adapter.
    
  • 
    Incoming Connections.
    

If the issue persists, we suggest that you try to
renew
your
IP address. To do this, follow these steps:

• 
  Open
  Command Prompt
  as
  Administrator.
  
• 
  Type the following command:
  
  • 
    Ipconfig/release
    and hit
    Enter.
    
  • 
    Ipconfig/renew
    and hit
    Enter.
    
  • 
    Exit.
    

Let us know how it goes.

Regards.

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?