Windows 10: How to disable/stop the widgets window to pop up every time I turn on or restart the computer?

every time I turn on or restart the computer the widgets window pops up and its annoying and make the computer to start slower.

:)

 

How to disable the windows resize widget.

Hi Carl,

The resizing widget on your screen isn't part of Windows 10, so it's possible that it's showing up due to a third-party program. We'd like to learn more about your concern so that we could provide the proper resolution. We just have a few questions for you:

• What is the make and model of your device?
  
• Did you make any changes to your computer before this started happening?

As an initial recommendation, we suggest performing a clean boot to find out if this behavior is caused
by a third-party program. This will load Windows with minimal drivers and programs, preventing software conflicts from occurring. If the widget doesn't appear in a clean boot environment, check the section How to determine what is causing
the problem by performing a clean boot for what to do next.

Note: To return your computer back to normal, check the section How to reset the computer to start normally after clean boot troubleshooting.

Additionally, we've found similar threads where this happens with Dell devices. If your computer was manufactured by Dell, check if you have an app called
Dell Premier Color. If you have this app, follow these steps:

• If you can see this app icon in the taskbar or the system tray, right-click it and choose
  Disable Display Splitter.
• If it's not in your taskbar or system tray, launch the app from the Start menu.
  
• Click Advanced in the upper right corner.
• On the left panel, click Display Splitter.
• Uncheck Display Splitter on.

If your computer was manufactured by MSI, this happens when Desktop Partition is enabled in the
True Color app. To disable it, follow these steps:

• Launch the True Color app from the Start menu.
• Go to the Tools tab.
• Disable the Desktop Partition On option.

We look forward to your response and the results of the initial troubleshooting.

 

STOP error after Windows MCE 2005 clean install

OK, found the rest of it.

A problem has been detected and Windows has been shut down to prevent damage to your computer.

If this is the first time you've seen Stop error screen, restart your computer. If this screen appears again, follow these steps:

Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive and make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

Technical information:

*** STOP: 0X0000007B (0xF7C7B524, 0XC0000034, 0X00000000, 0X00000000)

 

Windows 10 stop automatic restart

Hi Hemanth,

We appreciate you for being a part of Windows 10.

Before proceeding, we need more information to help you better.

• 
  Does the computer restarts only when you wake the system from sleep mode?
  
• 
  While the computer restarts, do you see that the updates are getting installed on the restart screen?
  

Until you reply to us with the required information, you may follow the below suggestions.

If the computer is restarting only while you wake it up from the sleep mode, follow the below steps and check if the computer is getting restarted even after scheduling the computer to restart at the particular time.

Step 1:

You may try to turn the sleep and display to never and check to isolate the issue.

• 
  Press Windows + R keys on the keyboard to open Run command.
  
• 
  Type powercfg.cpl to open the power settings.
  
• 
  Select your current plan and click on Change plan settings.
  
• 
  Change the Turn off the display and
  Put the computer to sleep to Never
  

If the issue still persists, follow the below step.

Step 2:

Turn off the hybrid sleep and check if it helps. (If it is turned on already in power settings)

• 
  Press Windows + R keys on the keyboard to open Run command.
  
• 
  Type powercfg.cpl to open the power settings.
  
• 
  Select your current plan and click on Change plan settings.
  
• 
  Click on Advanced Power settings.
  
• 
  Click on Change settings that are currently unavailable. (Enter administrator credentials if prompted)
  
• 
  Find the Sleep and double click on it.
  
• 
  Double click on Allow hybrid sleep and turn the settings to
  OFF.
  
• 
  Click on Apply and close the Power options window.
  

If the issue still persists, follow the below step.

Step 3:

Create the new power plan and check if it helps.

• 
  Press Windows + R keys on the keyboard to open Run command.
  
• 
  Type powercfg.cpl to open the power settings.
  
• 
  Click on Create a power plan on the left navigation pane.
  
• 
  Enter your new power plan name in the Plan name text box and click on
  Next.
  
• 
  Follow the below instructions and check if it helps.
  

I hope the above information helps. Kindly let us know if you need any further assistance with Windows. We are glad to assist you.

Thank you.