Windows 10: usb wifi adapter keeps having a problem starting- unable to use

I am trying to install a wifi dongle/ USB adapter to my laptop. windows 10. But it keeps saying 'Device USB\VID_0BDA&PID_B812\123456 had a problem starting.' I tried to install some cab files/ used windows update for drivers but no luckI bought it from amazon, brand is Axfee, couldn't find a website for it. Came in with a small CD but who has a CD reader nowadays? Thank you!

:)

 

Recommendation for WiFi usb / card

If you have a desktop computer I would STRONGLY suggest a PCIe adapter rather than a USB adapter if you go with WiFi 6. The only USB WiFi adapters that I have seen thus far use a Realtek chipset which is reported to have some serious flaws. In my own personal experience, I have tried 2 of these and returned both, getting performance worse than other WiFi 5 adapters and constant disconnects even 10 feet from my WiFi router. If you go with a USB adapter, I would suggest a quality WiFi 5 adapter. One more note: Should you decide to go with a WiFi 6 PCIe adapter, I would suggest a WiFi 6e model. They actually cost no more, and they are one step up just in case you ever go to a WiFi 6e router.

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?

 

WiFi Adapter question

To be honest, I keep losing my wifi connection and Im almost positive its not due to my internet connection or Router or anything like that. VERY often, everyday, all day it keeps happening. The troubleshooter always resolves it by "reset wifi-adapter" (I believe this is the step it takes that resolves the problem) before it happens again anyways. Its driving me nuts ! Most time when it suddenly goes out (the connection) all the networks that should be in "show available networks" or all but the one I was connected to, disappear. I run the troubleshooter and it ends in resetting the wifi adapter. And it works. 10 minutes later, it happens again. Im trying to pin down the problem here. Thank you for your help.